View CS61310-IL_1228919.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CS61310 T1 Line Interface Unit
Features
Provides T1 line interface No crystal needed for jitter attenuation Greater than 14 dB of transmit return loss Meets AT&T 62411 jitter tolerance and attenuation requirements Meets ANSI T1.231B requirements for LOS and AIS AWG for user programmable pulse shapes TX driver high impedance / low power control Generation and detection of loop up / loop down signaling Selectable unipolar or bipolar I/O Compliant with:
-- American National Standards (ANSI): T1.102, T1.105, T1.403, T1.408, and T1.231 -- FCC Rules and Regulations: Part 68 and Part 15 -- AT&T Publication 62411 -- TR-NET-00499
Description
The CS61310 is a T1 primary rate line interface unit. It combines the complete analog transmit-and-receive circuitry for a single, full-duplex interface at T1 rates. The device is pin- and function-compatible with the Level One LXT310. Enhanced functionality is available through an extended register set, allowing custom pulse shape generation as well as generation and detection of loop up and loop down codes. The CS61310 features crystal-less jitter attenuation.
ORDERING INFORMATION CS61310-IL
28-pin PLCC
TCLK TDATA/TPOS UBS/TNEG JASEL
2
3
4 11
E N C O D E R
JITTER ATTEN
TRANSMIT TIMING & CONTROL
PULSE SHAPING CIRCUITRY ROM / RAM
13
LINE DRIVERS
TTIP
16 28 26
TRING CLKE/TAOS CS/RLOOP SCLK/LLOOP SDI/LBO1 SDO/LBO2
TAOS Enable REMOTE LOOPBACK LOCAL LOOPBACK (DIGITAL)
LBO Select
SERIAL PORT
27 24 25
REGISTERS & CONTROL LOGIC LOS/ NLOOP Clear LLOOP Enable EQUALIZER CONTROL SLICERS & PEAK DETECT NOISE & CROSSTALK FILTERS
RCLK RDATA/RPOS
BPV/RNEG
8 7
6
D E C O D E R
LOCAL LOOPBACK (ANALOG) 18 LATN
JITTER ATTEN
TIMING & DATA RECOVERY
MAGNITUDE EQUALIZER
AGC
19 20
RTIP
RRING
INT/NLOOP LOS
23 12
INBAND NLOOP & LOS PROCESSOR 9
RECEIVE CLOCK GENERATOR
1
MCLK
10 XTALOUT
5 MODE
21 RV+
22
14
15 TV+
XTALIN
RGND TGND
Final Product Information
Cirrus Logic, Inc. http://www.cirrus.com
This document contains advanced information for a new product. Cirrus Logic reserves the right to modify this product without notice.
Copyright Cirrus Logic, Inc. 2003 (All Rights Reserved)
DS440F1 FEB `03 1
(c)
CS61310
TABLE OF CONTENTS
1. CHARACTERISTICS AND SPECIFICATIONS ........................................................................ 4 ABSOLUTE MAXIMUM RATINGS ........................................................................................... 4 RECOMMENDED OPERATING CONDITIONS ....................................................................... 4 DIGITAL CHARACTERISTICS ................................................................................................. 4 ANALOG CHARACTERISTICS ................................................................................................ 5 T1 SWITCHING CHARACTERISTICS ..................................................................................... 6 SERIAL PORT SWITCHING CHARACTERISTICS.................................................................. 8 2. THEORY OF OPERATION ....................................................................................................... 9 2.1 Interface Modes ................................................................................................................. 9 2.2 Master Clocks .................................................................................................................... 9 2.3 Transmitter ......................................................................................................................... 9 2.4 Transmit All Ones Select ................................................................................................. 10 2.4.1 Receiver .............................................................................................................. 10 2.4.2 Clock Recovery ................................................................................................... 10 2.4.3 Jitter Tolerance ................................................................................................... 10 2.5 Jitter Attenuator ............................................................................................................... 11 2.6 Receiver Line Attenuation Indication ............................................................................... 11 2.7 Receiver Loss of Signal ................................................................................................... 11 2.8 Local Loopback ................................................................................................................ 12 2.9 Remote Loopback ............................................................................................................ 12 2.10 Network Loopback ......................................................................................................... 12 2.11 Alarm Indication Signal .................................................................................................. 12 2.12 Serial Interface ............................................................................................................... 12 2.13 Control Register 1: Address 0x10 .................................................................................. 14 2.14 Control Register 2: Address 0x11 ................................................................................ 14 2.15 Equalizer Gain (EQGAIN): Address 0x12 ...................................................................... 15 2.16 RAM Address (RAM): Address 0x13 ............................................................................. 15 2.17 Interrupts ........................................................................................................................ 15 2.18 Power On Reset / Reset ................................................................................................ 16 2.19 Power Supply ................................................................................................................. 16
Contacting Cirrus Logic Support
For all product questions and inquiries contact a Cirrus Logic Sales Representative. To find one nearest you go to www.cirrus.com
IMPORTANT NOTICE "Preliminary" product information describes products that are in production, but for which full characterization data is not yet available. "Advance" product information describes products that are in development and subject to development changes. Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other parts of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. An export license and/or quota needs to be obtained from the competent authorities of the Chinese Government if any of the products or technologies described in this material is subject to the PRC Foreign Trade Law and is to be exported or taken out of the PRC. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK. Purchase of I2C components of Cirrus Logic, Inc., or one of its sublicensed Associated Companies conveys a license under the Phillips I2C Patent Rights to use those components in a standard I2C system. Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners.
2
DS440F1 FEB `03
CS61310
3. 4. 5. 6. ARBITRARY WAVEFORM GENERATION ............................................................................ 17 PIN DESCRIPTION ................................................................................................................. 20 PACKAGE DIMENSIONS ...................................................................................................... 25 APPLICATIONS ..................................................................................................................... 27
LIST OF FIGURES
Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Signal Rise and Fall Characteristics ............................................................................ 7 Recovered Clock and Data Switching Characteristics ................................................. 7 Transmit Clock and Data Switching Characteristics .................................................... 7 Serial Port Write Timing Diagram ................................................................................ 8 Serial Port Read Timing Diagram ................................................................................ 8 Typical Pulse Shape for DS-1 ...................................................................................... 9 Minimum Input Jitter Tolerance of Receiver .............................................................. 10 Typical Jitter Transfer Function .................................................................................. 11 LATN Pulse Width encoding ...................................................................................... 11 Input/Output Timing (showing address 0x10) ............................................................ 13 Phase Definition of Arbitrary Waveforms ................................................................... 17 Example of Summing of Waveforms .......................................................................... 17 Hardware Mode Operation ......................................................................................... 27 Matched Impedence Output Configuration ................................................................ 28
LIST OF TABLES
Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Pulse Shape Selection and Transformer Requirements ............................................... 9 Data Output/Clock Relationship.................................................................................. 10 Register Map............................................................................................................... 13 Register 16 Decoding ................................................................................................. 15 CS61310 Diagnostic Mode Availability ....................................................................... 18 Transformer Specification ........................................................................................... 19 Recommended Tranformers for the CS61310 ............................................................ 19
DS440F1 FEB `03
3
CS61310
1. CHARACTERISTICS AND SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes Parameter DC Supply Input Voltage, Any Pin Input Current, Any Pin Ambient Operating Temperature Storage Temperature (Note 1) (referenced to RGND=TGND=0 V) Symbol RV+ TV+ Vin Iin TA Tstg Min RGND-0.3 -10 -40 -65 Max 6.0 (RV+) + 0.3 (RV+) + 0.3 10 85 150 Units V V V mA C C
Notes: 1. Transient currents of up to 100 mA will not cause SCR latch-up. Also TTIP, TRING, TV+ and TGND can withstand a continuous current of 100 mA.
RECOMMENDED OPERATING CONDITIONS
Parameter DC Supply Ambient Operating Temperature Power Consumption (Notes 3, 4, 5) Symbol (Note 2) RV+, TV+ TA PC Min 4.75 -40 Typ 5.0 25 390 Max 5.25 85 630 Units V C mW
Notes: 2. TV+ must not exceed RV+ by more than 0.3 V. 3. Power consumption measured while driving line load over operating temperature range. Power consumption includes IC and load. Digital input levels are within 10% of the supply rails and digital outputs are driving a 50 pF capacitive load. 4. Typical consumption corresponds to 50% ones density and medium line length at 5.0 V. 5. Maximum consumption corresponds to 100% ones density and maximum line length at 5.25 V.
DIGITAL CHARACTERISTICS
(TA = -40C to 85C; TV+, RV+ = 5.0 V 5%; GND = 0 V) Parameter High-Level Input Voltage Low-Level Input Voltage High-Level Output Voltage IOUT = -40 A Low-Level Output Voltage IOUT = 1.6 mA Input Leakage Current (Note 6) PINS 1-4, 24-28 (Note 6) PINS 1-4, 24-28 (Notes 6, 7) PINS 6-8, 25 (Notes 6, 7) PINS 6-8, 25 Symbol VIH VIL VOH VOL Min 2.0 2.4 Typ Max 0.8 0.4 10 Units V V V V A
Notes: 6. This specification guarantees TTL compatibility (VOH = 2.4 V @ IOUT = -40 A). 7. Output drivers are TTL compatible and will drive CMOS logic levels into a CMOS load.
4
DS440F1 FEB `03
CS61310
ANALOG CHARACTERISTICS
(TA = -40C to 85C; TV+, RV+ = 5.0 V 5%; GND = 0 V) Parameter Transmitter AMI Output Pulse Amplitudes (Note 8) T1, (FCC Part 68) (Note 9) T1, DSX-1 (Note 10) (Note 12) 1.5 FCC DSX1 External Equalizer (Notes 11,12) 10 Hz - 8 kHz 8 kHz - 40 kHz 10 Hz - 40 kHz Broad Band (Notes 8, 12) 12.6 -29 -40 30 (Notes 12,14) T1, DSX-1 T1, (FCC Part 68) 160 0.4 138 44 44 44 0.015 0.015 0.015 0.020 15 -38 0.2 20k -42 50 50 175 190 17.9 0.5 50 UI UI UI UI dBm dB dB mA RMS dB mV dB % of peak % of peak bits UI UI 2.7 2.4 4.8 3.0 3.0 5.6 3.3 3.6 V V V Min Typ Max Units
External Equalizer Pulse Amplitude Transmitter Output Impedance Transformer turns ratio = 1:2 Transformer turns ratio = 1:1.5
Jitter Added by the Transmitter
Power in 2 kHz band about 772 kHz
Power in 2 kHz band about 1.544 MHz (Notes 8, 12) (referenced to power in 2 kHz band at 772 kHz) Positive to Negative Pulse Imbalance Transmitter Short Circuit Current Receiver RTIP/RRING Input Impedance Sensitivity Below DSX (0 dB = 3.0 V) Loss of Signal Threshold Data Decision Threshold (Notes 8, 12) (Notes 8, 13)
Allowable Consecutive Zeros before LOS Receiver Input Jitter Tolerance(Note 16) T1:10 kHz - 100 kHz (Note 12) 1 Hz
Notes: 8. Using a 0.47 F capacitor in series with the primary of a transformer recommended in the Applications Section. 9. Pulse amplitude measured at the secondary side of the transformer across a 100 load for line length setting LEN2/1/0 = 0/1/0. 10. Pulse amplitude measured at the DSX-1 Cross-Connect for all line length settings from LEN2/1/0 = 0/1/1 to LEN2/1/0 = 1/1/1. 11. Assuming that jitter free clock is input to TCLK. 12. Not production tested. Parameters guaranteed by design and characterization. 13. Measured broadband through a 0.5 resistor across the secondary of the transmitter transformer during the transmission of an all ones data pattern. 14. Data decision threshold established after the receiver equalizer filters pulse overshoot and undershoot. 15. Jitter tolerance for 0 dB input signal level. Jitter tolerance increases at lower frequencies. See Figure 7. 16. See Receiver Jitter Tolerance Plot, Figure 7. DS440F1 FEB `03 5
CS61310
T1 SWITCHING CHARACTERISTICS
(TA = -40C to 85C; TV+, RV+ = 5.0 V 5%; GND = 0 V; Inputs: Logic 0 = 0 V, Logic 1 = RV+; See Figures 1, 2, & 3) Parameter TCLK Frequency TCLK Duty Cycle MCLK Frequency RCLK Duty Cycle Rise Time, All Digital Outputs Fall Time, All Digital Outputs TPOS/TNEG to TCLK Falling Setup Time TCLK Falling to TPOS/TNEG Hold Time RPOS/RNEG Valid Before RCLK Falling RPOS/RNEG Valid Before RCLK Rising RPOS/RNEG Valid After RCLK Falling RPOS/RNEG Valid After RCLK Rising (Note 20) (Note 21) (Note 20) (Note 21) Symbol ftclk (Note 12) tpwh2/tpw2 (Note 17) fmclk (Notes 12, 18) tpwh1/tpw1 (Note 19) tr (Note 19) tf tsu2 th2 tsu1 tsu1 th1 th1 Min 45 45 25 25 150 150 150 150 Typ 1.544 50 1.544 50 274 274 274 274 Max 55 55 85 85 Units MHz % MHz % ns ns ns ns ns ns ns ns
Notes: 17. MCLK provided by an external source or TCLK. 18. RCLK duty cycle will be 62.5% or 37.5% when jitter attenuator FIFO limits are reached. 19. At max load of 1.6 mA and 50 pF. 20. Host Mode (CLKE = 1). 21. Host Mode (CLKE = 0)
6
DS440F1 FEB `03
CS61310
.
tr 90% 10% 90%
tf
Any
D ig ital O utp ut
10%
Figure 1. Signal Rise and Fall Characteristics
tpw 1
R C LK
(C L K E = 1 ) t pw l1
t su1
tpw h1
t h1
RP OS RN EG
(C L K E = 0 ) RC LK
Figure 2. Recovered Clock and Data Switching Characteristics
t p w2 t pw h2 TCLK t su2 T P O S /T N E G t h2
Figure 3. Transmit Clock and Data Switching Characteristics
DS440F1 FEB `03
7
CS61310
SERIAL PORT SWITCHING CHARACTERISTICS
(TA = -40 to 85C; TV+, RV+ = 5V 5%; Inputs: Logic 0 = 0 V, Logic 1 = RV+) Parameter SDI to SCLK Setup Time SCLK to SDI Hold Time SCLK Low Time SCLK High Time SCLK Rise and Fall Time CS to SCLK Setup Time SCLK to CS Hold Time CS Inactive Time SCLK to SDO Valid CS to SDO High Z Notes: 22. Output load capacitance = 50 pF
t cw h CS t cc SCLK t ch t cl t cc h
Symbol tdc tcdh tcl tch tr, tf tcc tcch tcwh (Note 22) tcdv tcdz
Min 50 50 240 240 50 50 250 -
Typ 100
Max 50 200 -
Units ns ns ns ns ns ns ns ns ns ns
000000 d c 000000 S D I 000000 L S B 000000 000000
t
t cdh
00000 00000 00000 00000 00000
B Y TE
000000 000000 000000 LS B 000000 000000
00000 00000 00000 00000 00000
DATA
000000 000000 000000 M S B 000000 000000
B Y TE
t cdh
00000000000000 00000000000000 00000000000000 00000000000000 00000000000000
C O N TR O L
Figure 4. Serial Port Write Timing Diagram
CS
SCLK
SDI
L A S T A D D R B IT
t cd v SDO C LK E = 0 t cd v
D0 D1 D6 D7
t cd z
H IG H Z SDO C LK E = 1
D0 D1 D6 D7
Figure 5. Serial Port Read Timing Diagram
8
DS440F1 FEB `03
CS61310
2. THEORY OF OPERATION
The CS61310 Line Interface Unit is a fully integrated transceiver for T1 long haul applications. The transmitter outputs all pulse shapes for T1 applications. 2.1 Interface Modes The CS61310 can be operated as a stand-alone device with its interface in hardware mode (MODE pin is low), or it can be operated by a microcontroller over a serial interface in host mode (MODE pin is high). Host mode enables the use of additional functionality, as described in the Serial Interface section. 2.2 Master Clocks The CS61310 requires a reference clock for the receiver and the jitter attenuator. A 1.544 MHz external clock can be input to MCLK, or a 4x crystal can be connected to the on-chip oscillator. This frequency reference should be within +32 ppm of the nominal operating frequency. Jitter and wander on the reference clock will degrade jitter attenuation and receiver jitter tolerance. If MCLK is provided, the crystal oscillator is ignored. 2.3 Transmitter The transmitter accepts digital T1 input data and drives appropriately shaped AMI (Alternate Mark Inversion) pulses onto a transmission line through a transformer. The transmit data (TPOS & TNEG or TDATA) is sampled on the falling edge of the input clock, TCLK. The pulse shapes comply with FCC Part 68 Option A (0 dB), Option B (-7.5 dB), Option C (-15 dB) or (-22.5 dB) (see Table 1). Pulse shaping and signal level are controlled by LBO1 and LBO2 pins in hardware mode, or the LBO1 and LBO2 bits (CR1.3 and CR1.4) in host mode. Custom transmit pulse shapes may be implemented by writing pulse shape coefficients to the registers. Custom pulses may be used to correct for pulse shape degradation or distortion caused by improper termination, suboptimal interconnect wiring, or loading from external components such as high voltage protection devices. For DS-1 applications, the arrangement in Table 1 meets ANSI T1.102 pulse shape requirements. A
LBO2 0 0 1 1 LBO1 0 1 0 1 Output Pulse 0 dB -7.5 dB -15 dB -22.5 dB
Table 1. Pulse Shape Selection and Transformer Requirements
typical output pulse is shown in Figure 6. These pulse settings can also be used to meet ITU-T pulse shape requirements for 1.544 MHz operation.
N O R M AL IZE D AM P L IT U D E 1 .0 A N S I T I.1 0 2 S P E C IFIC A T IO N
0 .5
0 O UTPUT P U L SE S H A PE -0 .5 0 250 5 00 750 T IM E (n a n o se co n d s) 1 00 0
Figure 6. Typical Pulse Shape for DS-1
Setting TNEG high for more than 16 TCLK cycles enables the coder mode, changing TPOS to TDATA, RPOS to RDATA, and RNEG to BPV. When configured for coder mode, the MODE pin can be tied to RCLK enabling the B8ZS encoders and decoders. The CS61310 will detect the absence of TCLK, and will force TTIP and TRING to high impedance
DS440F1 FEB `03
9
CS61310
after 175 bit periods, preventing transmission when data input is not present. In host mode, the transmitter can be set to high impedance by setting the TxHIZ bit (CR2.1) to "1." When any transmit control bit (TAOS, LEN0-2, LBO1-2, or LLOOP) is toggled, the transmitter outputs will require approximately 22 bit periods to stabilize. The transmitter will take longer to stabilize when RLOOP is selected because the timing circuitry must adjust to the new frequency. 2.4 Transmit All Ones Select The transmitter provides for all ones to be generated at TTIP and TRING. The timing of the bits is controlled by TCLK; if TCLK is absent, then MCLK is used; in the absence of MCLK, the quartz crystal generates the output timing. Transmit all ones is selected in hardware mode by setting the TAOS pin high (CR1.7 = 1 in host mode). When TAOS is active, the TPOS and TNEG (TDATA) inputs are ignored. If Remote Loopback is in effect, any TAOS request will be ignored. In the hardware mode, data on RPOS and RNEG (RDATA), is stable and latched on the rising edge of recovered clock, RCLK. In host mode, the CLKE pin determines the clock polarity for which output data is stable and valid (see Table 2). When CLKE is high, RPOS and RNEG (RDATA) are valid on the falling edge of RCLK. When CLKE is low, RPOS and RNEG are valid on the rising edge of RCLK.
MODE LOW HIGH CLKE Don't Care LOW DATA CLOCK RPOS RNEG RPOS RNEG SDO RPOS RNEG SDO RCLK RCLK RCLK SCLK RCLK RCLK SCLK Clock Edge for Valid Data Rising Rising Rising Falling Falling Falling Rising
HIGH
HIGH
2.4.1
Receiver
Table 2. Data Output/Clock Relationship
A noise and cross-talk filter removes signal components that are coupled onto the line from other cables. The clock and data recovery circuit exceeds the jitter tolerance specifications of Publication 43802, Publication 43801, AT&T 62411, and TR-TSY-000170. Jitter tolerance is shown in Figure 7. The RTIP and RRING inputs are biased to an intermediate DC level and treat the input signal differentially. The receiver extracts data and clock from the input signal. The receiver outputs are the clock and synchronized data. The incoming pulses are amplified, equalized and filtered before being fed to the comparator for peak detection, slicing and data recovery.
Setting TNEG high for more than 16 TCLK cycles enables the coder mode, changing TPOS to TDATA, RPOS to RDATA, and RNEG to BPV. When configured for coder mode, the MODE pin can be tied to RCLK enabling the B8ZS encoders and decoders.
2.4.3
Jitter Tolerance
The receiver jitter tolerance is shown in Figure 7. The CS61310 jitter tolerance exceeds AT&T 62411 for synchronizers.
M in im u m P erform ance
300 138 100 AT& T 6 2411 28
2.4.2
Clock Recovery
P E A K-TO -P E A K JIT T ER (un it inte rva ls)
10
The clock recovery circuit is a third-order phaselocked loop. The digital PLL in the clock recovery circuit of the CS61310 recovers clock from the edges of the incoming pulses (1's). The clock and data recovery circuit is tolerant of long strings of consecutive zeros, and will successfully receive a 1-in-175, jitter-free input signal.
1 .4
.1 1 10 100
300
700 1k
(H z)
1 0k
100k
JIT T ER F R EQ UE N C Y
Figure 7. Minimum Input Jitter Tolerance of Receiver
10
DS440F1 FEB `03
CS61310
2.5 Jitter Attenuator Jitter attenuation can be implemented in either the transmit (JASEL low) or receive (JASEL high) paths, or it can be eliminated from the circuit by setting the XTALIN pin high. The jitter attenuator on the CS61310 does not require a crystal. It is activated when XTALIN is either connected to ground or left open; connecting to ground is the preferred method. The jitter attenuator corner frequency is set at 4 Hz, with attenuation increasing at a 20 dB per decade rate above 4 Hz. A typical jitter attenuation graph is shown in Figure 8. 2.6 Receiver Line Attenuation Indication The LATN pin outputs a coded signal that represents the signal level at the input of the receiver. As shown in Figure 9, the LATN output is measured against RCLK to provide the signal level in 7.5 dB increments. In host mode, the receive input signal level can be read from the Equalizer Gain register, address 0x12, to greater resolution, dividing the input range into 20 steps of 2 dB increments.
0 M inim um A ttenuation Lim it 10 A tte nuation in d B 20 30 40 50 60 1 10 100 M ax im um Attenuation Lim it M eas ured P erform ance 1k 10 k 62411 R equirem ents
2.7 Receiver Loss of Signal The receiver will indicate loss of signal by setting the LOS pin high in hardware mode (CR1.0 = 1 in host mode). LOS is active on power up, reset, when receiver gain is maximized, upon receiving 175+/-15 consecutive zeros, or when the received signal power falls below below the signal level, "Loss of Signal Threshold" listed under Analog Specifications. Received zeros are counted based on recovered clock cycles. While in the LOS state, received data on RPOS/RNEG (RDATA in unipolar mode) equals 0 (squelched). The device complies with ANSI T1.231-1993 criteria to exit the LOS condition: 12.5% ones density for 175+/-75 bit periods with no more than 100 consecutive zeros. While LOS is active, RCLK depends on MCLK and the jitter attenuator. If the jitter attenuator is in the transmit path or not used, RCLK is referenced to MCLK, if provided, or the crystal oscillator otherwise. If the jitter attenuator is in the receive path, the jitter attenuator will hold the average incoming data frequency prior to LOS. The recovered clock remains at a 50% duty cycle. The RPOS (RDATA) and RNEG pins are forced low during LOS. Timing is recovered by a phase selector which selects one of the phases from the internal synchronization clock (one of three clocks, 120 degrees apart in phase, at 16X of the data rate). Since the selection is made between a limited set of phases, the Digital Timing Recovery process has a small phase error built into the sampling process. By choosing from 48 possible sampling phases, the CS61310 reduces the sampling error to a minimum.
Frequenc y in Hz
Figure 8. Typical Jitter Transfer Function
R CLK
L A TN
1
2
3
4
5
L A TN = 1 R C LK , 7 .5 d B o f A tten u atio n L A TN = 2 R C LK , 1 5 d B of A tte nu a tio n L A TN = 3 R C LK , 2 2 .5 d B o f A tten u ation
L A TN = 4 R C LK , 0 d B o f A tte n ua tio n
Figure 9. LATN Pulse Width encoding DS440F1 FEB `03 11
CS61310
2.8 Local Loopback In hardware mode, local loopback is selected by setting the LLOOP pin high (CR1.6 = 1 in host mode). Selecting local loopback causes clock and data presented on TCLK, TPOS/TNEG (TDATA) to be output at RCLK, RPOS/RNEG (RDATA). Local loopback disconnects the RTIP/RRING inputs from the line. Inputs to the transmitter are still transmitted on TTIP and TRING, unless TAOS has been selected in which case, AMI-encoded continuous ones are transmitted at the TCLK frequency. The receiver RTIP and RRING inputs are ignored when local loopback is in effect. 2.9 Remote Loopback Remote loopback is selected by setting the RLOOP pin high in hardware mode (CR1.5 = 1 in host mode). In remote loopback, the recovered clock and data input on RTIP and RRING are sent back out on the line via TTIP and TRING. Selecting remote loopback overrides a TAOS request. The recovered clock is also sent to RCLK, and the recovered data is also sent to RPOS and RNEG in bipolar mode, or RDATA in unipolar mode. Simultaneous selection of local and remote loopback modes will cause a device reset to occur (see Reset). 2.10 Network Loopback Network Loopback (automatic remote loopback) can be commanded from the network when the Network Loopback detect function is enabled. In Host Mode, Network Loopback (NLOOP) detection is enabled by writing ones to TAOS, LLOOP, and RLOOP, then clearing these three bits on a successive write cycle. In hardware mode, Network Loopback can be enabled by tying RLOOP to RCLK or by setting TAOS, LLOOP, and RLOOP high for at least 200 ns, and then low. Once enabled Network Loopback functionality will remain in effect until RLOOP is activated or the device is reset. When NLOOP detection is enabled, the receiver monitors the input data stream for the NLOOP data patterns (00001 = enable, 001 = disable). When an NLOOP enable data pattern is repeated for a minimum of five seconds (with less than 10E-3 BER), the device initiates a remote loopback. Once Network Loopback detection is enabled and activated by the NLOOP data pattern, the loopback is identical to Remote Loopback initiated at the device. NLOOP is reset if the disable pattern (001) is received for 5 seconds, or by activation of RLOOP. NLOOP is temporarily suspended by LLOOP, but the NLOOP state is not reset. 2.11 Alarm Indication Signal The receiver sets the register bit, AIS, to "1" when less than 9 zeros are detected out of 8192 bit periods. AIS returns to "0" upon the first read after the AIS condition is removed, determined by 9 or more zeros out of 8192 bit periods. 2.12 Serial Interface In the Host Mode, pins 24 through 28 serve as a microcontroller interface. On-chip registers can be written to via the SDI pin or read from via the SDO pin at the clock rate determined by SCLK. Through these registers, a host controller can be used to control operational characteristics and monitor device status. The serial port read/write timing is independent of the system transmit and receive timing. Data transfers are initiated by taking the chip select input, CS, low (CS must initially be high). Address and input data bits are clocked in on the rising edge of SCLK. The clock edge on which output data is stable and valid is determined by CLKE as shown in Table 2. Data transfers are terminated by setting CS high. CS may go high no sooner than 50 ns after the rising edge of the SCLK cycle corresponding to the last write bit. For a serial data read, CS may go high any time to terminate the output and set SDO to high impedance. Figure 10 shows the timing relationships for data transfers when CLKE = 0. When CLKE = 1, data bit D7 is held until the falling edge of the 16th clock cycle. When CLKE = 0, data bit D7 is held valid until the rising edge of the 17th clock cycle. SDO goes high-impedance after CS goes high or at the end of the hold period of data bit D7. SDO goes to a high impedance state when not in use. SDO and SDI may be tied together in applications where the host processor has a bi-directional I/O port.
12
DS440F1 FEB `03
CS61310
An address/command byte, shown in Figure 10, points to addresses 0x10 through 0x15 (address 0x10 shown), and precedes a data byte. The first bit of the address/command byte determines whether a read or a write is requested. The next six
CS SC LK SDI SDO C LKE = 0 R /W 0 0 0 0 1 0 0 D0 D0 D1 D1 D2 D3 D4 D5 D a ta Input/O utp ut D2 D3 D4 D5 D6 D6 D7 D7
bits contain the address. The last bit is ignored. Data to the internal registers is input on the eight clock cycles immediately following the address/command byte.
A ddre ss/C o m m a nd Byte
Figure 10. Input/Output Timing (showing address 0x10)
7
6
LLOOP RAMPLSE X 0
5
RLOOP RSVD set to "0" X 0
4
LB02 LOOPDN EQ4 0
3
LB01 LOOPUP EQ3 0
2
CODER TAZ RPWDN EQ2 0
1
NLOOP TxHIZ EQ1 0
0
LOS RSVD set to "0" EQ0 LSB 0
ADDR
0x10 R/W 0x11 R/W 0x12 R 0x13 R/W 0x14
Control Register 1 TAOS
(CR1) (CR2)
Control Register 2 Equalizer Gain
(EQGAIN)
AIS X MSB 0
RAM Address
(RAM)
Reserved
Set to "0"
Table 3. Register Map
DS440F1 FEB `03
13
CS61310
2.13 Control Register 1: Address 0x10
6 LLOOP 5 RLOOP 4 LBO2 3 LBO1 2 CODER TAZ 1 NLOOP 0 (LSB) LOS
7 (MSB) TAOS
TAOS LLOOP
Transmit All Ones Select When TAOS = 1, all ones are transmitted at the TCLK frequency Local Loopback When LLOOP = 1, data input at TPOS, TNEG (TDATA) is internally looped back and output on RPOS, RNEG (RDATA). TCLK is routed to RCLK, through the jitter attenuator, if activated. Remote Loopback When RLOOP = 1, clock and data recovered by the receiver are sent back through the transmit path and retransmitted. The clock and data are routed through the jitter attenuator, if activated. Line BuildOut LBO2 LBO1 0 0 0 1 1 0 1 1 Attenuation 0 dB -7.5 dB -15 dB -22.5 dB
RLOOP
LBO2, 1
CODER (TAZ)
Zero Substitution (valid only when TNEG (UBS) is tied high, invoking coder mode). Setting CODER to "1" enables B8ZS encoding and decoding. When not in coder mode (TPOS/TNEG are data inputs) setting TAZ to "1" causes all zeros to be transmitted. Network Loopback NLOOP = 1 when a network loopback code has been detected on the received signal. An interrupt will occur when NLOOP changes state unless a "1" is written to NLOOP disabling the interrupt. Loss Of Signal LOS = 1 when the loss of signal criteria have been met (175 zeros). LOS = 0 when a valid signal is being received. An interrupt will occur when LOS changes state unless a "1" is written to LOS disabling the interrupt.
NLOOP
LOS
2.14
Control Register 2: Address 0x11
6 RAMPLSE 5 RSVD set to "0" 4 LOOPDN 3 LOOPUP 2 RPWDN 1 TxHIZ 0 (LSB) RSVD set to "0"
7 (MSB) AIS
AIS
Alarm Indication Signal. AIS = 1 when an all ones pattern is present at the receiver. This bit is reset to "0" by the first read occurring after the AIS condition has cleared. An interrupt will occur when AIS is present unless a "1" is written to AIS disabling the interrupt. When RAMPLSE = 1, output pulse shapes are determined by the codes in the internal, programmable, transmit RAM. Loop Down Setting LOOPDN to "1" causes the data pattern 001... to be repetitively transmitted. DS440F1 FEB `03
RAMPLSE LOOPDN
14
CS61310
LOOPUP RPWDN TxHIZ RSVD Loop Up Setting LOOPUP to "1" causes the data pattern 00001... to be repetitively transmitted. Receiver Power Down When RPWDN = 1, the receiver circuitry is powered down, but the transmitter is still active. Transmitter High Impedance When TxHIZ = 1 the transmitter goes to a low-power, high-impedance state Reserved. Set to 0 for proper operation.
2.15
Equalizer Gain (EQGAIN): Address 0x12
6 X 5 X 4 EQ4 3 EQ3 2 EQ2 1 EQ1 0 (LSB) EQ0
7 (MSB) X
EQ[4:0]
The receive equalizer gain settings are broken down into 20 segments and provided at the five LSBs of this register, EQ4 - EQ0. 00001 corresponds to -2 dB, 10100 corresponds to -40 dB. The three MSBs are don't cares.
2.16
RAM Address (RAM): Address 0x13
6 RAM.6 5 RAM.5 4 RAM.4 3 RAM.3 2 RAM.2 1 RAM.1 0 (LSB) RAM.0
7 (MSB) RAM.7
RAM[7:0]
The RAM address pointer for the arbitrary waveform memory; a special write procedure must be followed to write the waveform RAM.
2.17 Interrupts An interrupt will occur (INT pulls low) in response to a change in the LOS, AIS or NLOOP bits. The interrupt is cleared when the host processor writes a "1" to the respective bit in the control register. Writing a "1" to LOS or NLOOP over the serial interface has three effects: 1) The current interrupt on the serial interface will be cleared. (Note that simply reading the register bits will not clear the interrupt). Output data bits 5, 6 and 7 will be reset as appropriate. Interrupts for the corresponding LOS and NLOOP will be prevented from occurring.
is the RAM address register for the arbitrary waveform. Two consecutive address bytes are written; first the Address/Command Byte is written to address 0x13, followed by the address in RAM to be written. This dual address is then followed by the data byte for the waveform amplitude. There are 42 RAM byte locations (numbered h00 to h29).
Bits Status 7 0 0 0 0 1 1 1 1 6 0 0 1 1 0 0 1 1 5 0 Reset has occurred, or no program input 1 RLOOP active 0 LLOOP active 1 LOS has changed state since last Clear LOS occurred 0 TAOS active 1 NLOOP has changed state since last Clear NLOOP occurred 0 TAOS and LLOOP active 1 LOS and NLOOP have both changed state since last Clear NLOOP and Clear LOS Table 4. Register 16 Decoding 15
2) 3)
Writing a "0" to either LOS or NLOOP enables the corresponding interrupt for LOS and NLOOP. Reading the registers returns their current status or setting. Register 16 outputs the status NLOOP and LOS and has bits 5, 6, and 7 encoded as shown in Table 4. Writing the arbitrary waveform RAM requires a deviation from normal serial port access. Register 19
DS440F1 FEB `03
CS61310
2.18 Power On Reset / Reset Upon power-up, the IC is held in a static state until the supply crosses a threshold of approximately 3 Volts. When this threshold is crossed, the device will delay for about 10 ms to allow the power supply to reach operating voltage. After this delay, calibration of the transmit and receive sections commences. Because power up conditions can vary considerably, it is recommended that the device be reset after the power supply has stabilized to ensure a known initial operational condition. The internal frequency generators can be calibrated only if a reference clock is present. The reference clock for the transmitter is provided by TCLK. The reference for the receiver is either the crystal oscillator or MCLK. If both the oscillator and MCLK are active, MCLK will be used as the reference source. The initial calibration should take less than 20 ms after pulses are input to the receiver. In operation, the device is continuously calibrated, making the performance of the device independent of power supply or temperature variations. The continuous calibration function forgoes any requirement to reset the line interface when in operation. However, a reset function is available which will reinitiate calibration and clear all registers and clear the Network Loopback function. In Host Mode, a reset is initiated by simultaneously writing RLOOP and LLOOP to the register. The reset will set all registers to "0" and initiate a calibration. In Hardware Mode, the CS61310 is reset by simultaneously setting RLOOP and LLOOP high for at least 200 ns. Hardware reset will clear Network Loopback functionality 2.19 Power Supply The device operates from a single +5 Volt supply. Separate pins for transmit and receive supplies provide internal isolation. These pins should decoupled to their respective grounds. Decoupling and filtering of the power supplies is crucial for the proper operation of the analog circuits in both the transmit and receive paths. A 47F tantalum and 1.0F mylar or ceramic capacitor should be connected between TV+ and TGND, and a 0.1F mylar or ceramic capacitor should be connected between RV+ and RGND. Place capacitors as closely as possible to their respective power supply pins. Wire-wrap breadboarding of the line interface is not recommended because lead resistance and inductance serve to defeat the function of the decoupling capacitors.
16
DS440F1 FEB `03
CS61310
3. ARBITRARY WAVEFORM GENERATION
In addition to the predefined pulse shapes, the user can create custom pulse shapes using the host mode. This flexibility allows the board designer to accommodate non-standard cables, EMI filters, protection circuitry, etc. The arbitrary pulse shape of mark (a transmitted "1") is specified by describing it's pulse shape across three Unit Intervals (UIs). This allows, for example, the long haul return-to-zero tail to extend into the next UI, or two UIs, as is required for isolated pulses. Each UI is divided into multiple phases, and the users defines the amplitude of each phase. The waveform of a space (a transmitted "0") is fixed at zero volts. Examples of the phases are shown in Figure 11. In all cases, to define an arbitrary waveform, the user writes to the Waveform Register either 36, 39 or 42 times (12, 13 or 14 phases per UI for three UIs). The phases are written in the order: UI1/phase1, UI1/phase2, ... , UI1/phase14, UI2/phase1, ... , UI2/phase14, UI3/phase1, ... , UI3/phase14. For DSX-1 and DS1 applications, the CS61310 divides the 648 ns UI into 13 uniform phases (49.8 ns each), and will ignore the phase amplitude information written for phase 14 of each UI. When transmitting pulses, the CS61310 will add the amplitude information from the prior two symbols with the amplitude of the first UI of the current symbol before outputting a signal on TTIP/TRING. Therefore, a mark preceded by two spaces will be output exactly as the mark is programmed. However, when one mark is preceded by marks, the first portion of the last mark may be modified. With AMI data, where successive pulses have opposite polarity, the undershoot tail of one pulse will cause the rising edge of the next mark to rise more quickly, as shown in Figure 12. The amplitude of each phase is described by a 7bit, 2's complement number, where a positive value describes pulse amplitude, and a negative value describes pulse undershoot. The positive full value is hex 3F. The negative full value is hex 40. For T1, the typical output voltage is 38 mV/LSB (peak voltage across the TTIP and TRING outputs). On the secondary of a 1:2 step-up transformer, the mV/LSB is twice the values stated above. Note that although the full scale digital input is 3F, it is recommended that full scale output voltage on the transformer primary be limited to 2.4 Vpk. At higher output voltages, the driver may not drive the requested output voltage. The amplitude information for all phases is written via the serial-port to Arbitrary Pulse Shape registers as described in an earlier section. Each phase
D S X -1 (54 % d uty cy cle) A rbitrary W av eform E x am ple
D S -1 (5 0 % d uty cyc le ) Arb itrary W a vefo rm E xam ple
Figure 12. Example of Summing of Waveforms
Figure 11. Phase Definition of Arbitrary Waveforms
DS440F1 FEB `03
17
CS61310
amplitude is written as an eight-bit byte, where the first phase of the symbol is written first. In serial-port host mode, the amplitude bytes are written LSB first. The contents of the Arbitrary Waveform register can be verified by reading the Waveform Register.
Availability (Note 1) H/W Host Yes Yes Yes Yes No Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Host Mode (Note 2) Maskable No No Yes No No No Yes Yes No
Diagnostic Mode Loopback Modes Local Loopback (LLOOP) Remote Loopback (RLOOP) In-band Network Loopback (NLOOP) Internal Data Pattern Generation and Detection Transmit All Ones (TAOS) In-band Loop-up/down Code Generator Error Detection Bipolar Violation Detection (BPV) Alarm Condition Monitoring Receive Loss of Signal Monitoring (LOS) Receive Alarm Indication Signal Monitoring (AIS) Other Diagnostic Reports Receive Line Attenuation Indicator (LATN)
Table 5. CS61310 Diagnostic Mode Availability Notes: 1. In Hardware Mode the Diagnostic Modes are selected by directly setting the pins on the device; in Host Mode, the appropriate register bits are written for Diagnostic Modes. 2. In Host Mode the interrupts can be masked by writing a "1" to the LOS bit; there is no masking in the Hardware Mode.
18
DS440F1 FEB `03
CS61310
Turns ratio Primary inductance Primary leakage inductance Secondary leakage inductance Interwinding capacitance ET-constant
1:1.5, 1:2 step-up transmit, 1:1 receive 1.2 mH min at 772 kHz 0.5 H max at 772 kHz with secondary shorted 0.5 H max at 772 kHz 40 pF max, primary to secondary 16 V-s min Table 6. Transformer Specification
Turns Ratio(s)
Manufacturer Pulse Engineering Valor Schott Valor Schott Pulse Engineering Valor Schott Valor Schott Pulse Engineering Schott Valor Schott Pulse Engineering Valor Pulse Engineering Pulse Engineering Valor Pulse Engineering Pulse Engineering Valor Pulse Engineering Pulse Engineering
Part Number PE-64936 PT5008 67130840 ST5085 31187 PE-65351 PT5004 617130850 ST5086 31188 T-1054 31705 ST5074 31706 PE-68678 ST5162 PE-68877 T-1068 ST5173 T-1031 T-1022 ST5221 T-1077 T-1081
Package Type
1.5 kV, through-hole, single 1.5 kV, surface mount, single 1.5 kV, through-hole, single 1.5 kV, surface mount, single 1.5 kV, through-hole, single 1.5 kV, surface mount, single 1.5 kV, surface mount, dual 1.5 kV, surface mount, dual extended temp. 1.5 kV, surface mount, quad port 3 kV, surface mount, dual 1.5 kV, surface mount, dual 1.5 kV, surface mount, dual extended temp 3 kV, surface mount, dual
1:1CT
1:2CT
1:1.5CT
1:1CT 1:2CT
1:1CT 1:1.5CT
Table 7. Recommended Tranformers for the CS61310
DS440F1 FEB `03
19
CS61310
4. PIN DESCRIPTION
MCLK TCLK TPOS/TDATA TNEG/UBS MODE RNEG/BPV RPOS/RDATA RCLK XTALIN XTALOUT JASEL LOS TTIP TGND TAOS/CLKE LLOOP/SCLK RLOOP/CS LBO2/SDO LBO1/SDI NLOOP/INT RGND RV+ RRING RTIP LATN NC TRING TV+
MCLK TCLK TPOS/TDATA TNEG/UBS MODE RNEG/BPV RPOS/RDATA RCLK XTALIN XTALOUT JASEL LOS TTIP TGND
5 6 7 8 9 10 11 12 13 14 15 16 17 18 top view 4 3 2 1 28 27 26 25 24 23 22 21 20 19
TAOS/CLKE LLOOP/SCLK RLOOP/CS LBO2/SDO LBO1/SDI NLOOP/INT RGND RV+ RRING RTIP LATN NC TRING TV+
20
DS440F1 FEB `03
CS61310
Power Supplies TGND - Ground Transmit Driver, Pin 14.
Power supply ground for the transmit driver; typically 0 Volts.
TV+ - Power Supply, Transmit Driver, Pin 15.
Power supply for the transmit driver; typically +5 Volts.
RV+ - Power Supply, Pin 21.
Power supply for all subcircuits except the transmit driver; typically +5 Volts.
RGND - Ground, Pin 22.
Power supply ground for all subcircuits except the transmit driver; typically 0 Volts.
Oscillator XTALIN, XTALOUT - Crystal Connections, Pins 9 and 10.
A 6.176 MHz crystal can be connected across these pins. This oscillator provides the reference frequency for the LIU if MCLK is not provided. The load capacitance presented to the crystal by these pins should be approximately 19pF (IC and package, when soldered into a circuit board). The jitter attenuator may be disabled by tying XTALIN to RV+ through a 1k resistor, and floating XTALOUT. When pin 9 has no clock input, a clock must be supplied to the MCLK pin. Alternatively an external 6.176 MHz clock can be driven into XTALIN, and the jitter attenuator circuit will operate. If MCLK is provided, and XTALIN is tied low or left floating, the jitter attenuator will be enabled.
Control MCLK - Master Clock Input, Pin 1.
Either MCLK or the crystal oscillator provide the master frequency reference for the CS61310. If both MCLK and the crystal oscillator are present, the oscillator is ignored. MCLK should be 1.544 MHz. If MCLK is not used, it must be grounded.
MODE - Mode Select Input, Pin 5.
Setting the MODE pin high puts the CS61310 into Host Mode where the device is controlled by a microprocessor, via a serial port. Setting the MODE pin low, configures the part for hardware mode control where various control and status are provided on dedicated pins. The MODE pin is internally pulled down placing the part in Hardware Mode when this pin is left floating. Tying the MODE pin to RCLK places the chip in Hardware Mode and enables the B8ZS encoder/decoder (provided that coder mode has been enabled; see the description for TNEG/UBS pin).
JASEL - Jitter Attenuator Select, Pin 11.
If the jitter attenuator is enabled (crystal oscillator active, or XTALIN tied low or left floating with MCLK provided), setting JASEL high places the jitter attenuator in the receive path; setting JASEL low places the jitter attenuator in the transmit path.
NC - No Connect, Pin 17.
The input voltage to this pin does not effect normal operation.
DS440F1 FEB `03
21
CS61310
LBO1, LBO2 - Line Build Out 1 and 2, Pins 24 and 25 (Hardware Mode).
Transmitted line build out pulse shapes are selected by setting LBO1/2: 0/0 = 0 dB, 0/1 = -7.5 dB, 1/0 = -15 dB, and 1/1 = -22.5 dB.
RLOOP - Remote Loopback Input, Pin 26 (Hardware Mode).
Setting RLOOP to a logic 1 causes the received signal to be passed through the jitter attenuator (if active) and retransmitted onto the line. The internal encoders/decoders will be bypassed in Remote Loopback. Simultaneously setting RLOOP and LLOOP high while TAOS is low resets the CS61310. Simultaneously setting RLOOP, LLOOP and TAOS high enables Network Loopback detection.
LLOOP - Local Loopback Input, Pin 27(Hardware Mode).
Setting LLOOP to a logic 1 internally routes the transmitter input to the receiver output. If TAOS is low, the signal being output from the transmitter will be internally routed to the receiver inputs allowing nearly the entire chip to be tested. If TAOS and LLOOP are set high at the same time, the local loopback will occur at the jitter attenuator (excluding the transmit and receive circuitry) and the transmitter will transmit all ones. Simultaneously setting RLOOP and LLOOP high while TAOS is low resets the CS61310. Simultaneously setting RLOOP, LLOOP and TAOS high enables Network Loopback detection.
TAOS - Transmit All Ones Select Input, Pin 28 (Hardware Mode).
Setting TAOS to logic 1 causes continuous ones to be transmitted at the TCLK frequency. When TAOS is high, TPOS and TNEG (TDATA) are not output at the TTIP/TRING pins. TAOS is overridden by Remote Loopback. Setting TAOS, LLOOP, and RLOOP high simultaneously enables Network Loopback detection.
Status LOS - Loss Of Signal Output, Pin 12.
LOS goes high when 175 consecutive zeros are received. LOS returns low when the ones density reaches 12.5% (based on 175 consecutive bit periods, starting with a one and containing less than 100 consecutive zeros, as prescribed in ANSI T1.231-1993).
LATN - Line Attenuation Indication Output, Pin 18.
LATN is an encoded output that indicates the receive equalizer gain setting in relation to a five RCLK cycle period. If LATN is high for one RCLK cycle, the equalizer is set for 7.5 dB gain, two cycles = 15 dB gain, three cycles = 22.5 dB gain, four cycles = 0 dB. LATN may be sampled on the rising edge of RCLK.
NLOOP - Network Loopback Output, Pin 23 (Hardware Mode).
NLOOP goes high when a 00001 pattern is received for five seconds putting the CS61310 into network (remote) loopback. Network loopback is deactivated upon receipt of a 001 pattern for five seconds, or by the selection of RLOOP. Network loopback is temporarily suspended with LLOOP, but the state of the NLOOP pin does not change.
Serial Control Interface INT - Interrupt Output, Pin 23 (Host Mode).
INT pulls low to flag the host processor when NLOOP, AIS or LOS changes state. INT is an open drain output and should be tied to the supply through a resistor.
SDI - Serial Data Input, Pin 24 (Host Mode).
Data input to the on-chip register is sampled on the rising edge of SCLK. 22 DS440F1 FEB `03
CS61310
SDO - Serial Data Output, Pin 25 (Host Mode).
Status and control information are output from the on-chip register on SDO. If CLKE is high, SDO is valid on the rising edge of SCLK. If CLKE is low, SDO is valid on the falling edge of SCLK. SDO goes to a high-impedance state when the serial port is being written to, or after bit D7 is output or CS goes high (whichever occurs first).
CS - Chip Select, Pin 26 (Host Mode).
The serial interface is accessible when CS transitions from high to low.
SCLK - Serial Clock Input, Pin 27 (Host Mode).
SCLK is used to write or read data bits to or from the serial port registers.
CLKE - Clock Edge Input, Pin 28 (Host Mode).
Setting CLKE to logic 1 causes RPOS and RNEG (RDATA) to be valid on the falling edge of RCLK, and SDO to be valid on the rising edge of SCLK. Conversely, setting CLKE to logic 0 causes RPOS and RNEG (RDATA) to be valid on the rising edge of RCLK and SDO to be valid on the falling edge of SCLK.
Data Input/Output TCLK - Transmit Clock Input, Pin 2.
The 1.544 MHz transmit clock is input on this pin. TPOS and TNEG or TDATA are sampled on the falling edge of TCLK.
TPOS/TNEG - Transmit Positive Pulse, Transmit Negative Pulse, Pins 3 and 4.
Data input to TPOS and TNEG is sampled on the falling edge of TCLK and transmitted onto the line at TTIP and TRING. An input on TPOS results in transmission of a positive pulse; an input on TNEG results in transmission of a negative pulse. If TNEG, pin 4, is held high for 16 TCLK cycles, the CS61310 reconfigures for unipolar (single pin NRZ) data input at pin 3, TDATA. If TNEG goes low the CS61310 switches back to two-pin bipolar data input format.
TDATA - Transmit Data, Pin 3.
When pin 4, TNEG/UBS, is held high, pin 3 becomes TDATA, a single-line NRZ (unipolar) data input sampled on the falling edge of TCLK.
UBS - Unipolar / Bipolar Select, Pin 4.
When UBS is held high for 16 consecutive TCLK cycles (15 consecutive bipolar violations) the CS61310 reconfigures for unipolar (single-line NRZ) data input / output format. Pin 3 becomes TDATA, pin 7 becomes RDATA, and pin 6 becomes BPV.
NEG/RPOS - Receive Negative Pulse, Receive Positive Pulse, Pins 6 and 7.
Recovered data output on RPOS and RNEG is stable and valid on the rising edge of RCLK in Hardware Mode. In Host Mode, CLKE determines the edge of RCLK on which RPOS and RNEG are valid. A positive pulse on RTIP with respect to RRING generates a logic 1 on RPOS; a positive pulse on RRING with respect to RTIP generates a logic 1 on RNEG.
BPV - Bipolar Violation, Pin 6.
When pin 4 (TNEG/UBS) is held high, received bipolar violations are flagged by BPV (RNEG) going high along with the offending bit output from RDATA. If the B8ZS encoder/decoder is activated, BPV will not flag bipolar violations resulting from valid zero substitutions.
DS440F1 FEB `03
23
CS61310
RRDATA - Received Data, Pin 7.
Unipolar data (single-line NRZ) data is output on RDATA when pin 4, TNEG/UBS, is held high.
RCLK - Recovered Clock Output, Pin 8.
RCLK outputs the clock recovered from the input signal at RTIP and RRING. In a Loss of Signal state RCLK is driven either by MCLK or the crystal oscillator, or retains the frequency prior to the LOS state, depending on the clocks provided. While LOS is true, RCLK will be driven either by MCLK or the crystal oscillator. If the jitter attenuator is in the receive path, RCLK will make a smooth transition to the LOS timing. RCLK will remain at its frequency prior to LOS.
RTIP,RRING - Receive Tip, Receive Ring, Pins 19,20.
The B8ZS signal received from the line is input via these pins. A 1:1 transformer and appropriate matching resistors are required as shown in the applications section. Data and clock recovered from the signal input on these pins is output via RPOS, RNEG, and RCLK.
TTIP, TRING - Transmit Tip, Transmit Ring, Pins 13,16
These pins are the output of the differential transmit driver. The transformer and matching resistors can be chosen to give the desired pulse height (see Application Schematics)
24
DS440F1 FEB `03
CS61310
5. PACKAGE DIMENSIONS
28 PIN PLASTIC (PDIP) PACKAGE DRAWING
D E 1 SEATING PLANE e b A A1 b1 L
c eA
TOP VIEW
SIDE VIEW
BOTTOM VIEW
INCHES DIM A A1 b b1 c D E e eA L MIN 0.155 0.020 0.014 0.040 0.008 1.435 0.540 0.095 0.600 0.125 0 MAX 0.200 0.040 0.022 0.065 0.015 1.465 0.560 0.105 0.625 0.150 15
MILLIMETERS MIN MAX 3.94 5.08 0.51 1.02 0.36 0.56 1.02 1.65 0.20 0.38 36.45 36.83 13.72 14.22 2.41 2.67 15.24 15.87 3.18 3.81 0 15
1. Positional tolerance of leads shall be within 0.25 mm (0.010 in.) at maximum material condition, in relation to seating plane and each other. 2. Dimension eA to center of leads when formed parallel. 3. Dimension E does not include mold flash.
DS440F1 FEB `03
25
CS61310
28L PLCC PACKAGE DRAWING
e D2/E2
E1 E
B
D1 D A
A1
INCHES DIM A A1 B D D1 D2 E E1 E2 e MIN 0.165 0.090 0.013 0.485 0.450 0.390 0.485 0.450 0.390 0.040 MAX 0.180 0.120 0.021 0.495 0.456 0.430 0.495 0.456 0.430 0.060 JEDEC #: MS-018
MILLIMETERS MIN MAX 4.043 4.572 2.205 3.048 0.319 0.533 11.883 12.573 11.025 11.582 9.555 10.922 11.883 12.573 11.025 11.582 9.555 10.922 0.980 1.524
26
DS440F1 FEB `03
CS61310
6. APPLICATIONS
+ 33 F RGND 28 1 Control & Monitor 26 27 12 23 11 5 7 6 F ram e F o rm a t E n c o d e r/ D ec od e r 8 3 4 2 9 10 TAOS MCLK RLOOP LLOOP LOS NLO OP JASE L MODE RPOS RNEG RCLK TPOS TNEG TCLK X T A L IN XTALOUT RGND 22 TGND 14 T R IN G 13 T T IP R4 6 1:2 PE-65351 16 R3 0 .4 7 F 2 1 TRANSMIT 5 LINE CS61310 IN HARDWARE MODE R T IP 19 R1 20 R2 0 .47 F 5 1CT:1 PE-64936 6 1 2 R E C E IV E L IN E LB O2 LB O1 24 25 Lin e L en g th S e tting 0 .1 F 21 RV+ 15 TV+ + 1 .0 F
100
TGND
R1 () R2 () R3 () R4 ()
50 50 9.1 9.1
R R IN G
NOTE: The 0.47F capacitor between R1 & R2 may be omitted if common mode noise is not an issue. NOTE: The optional 0.47F DC blocking cap eliminates DC saturation current through T2 Figure 13. Hardware Mode Operation
DS440F1 FEB `03
27
CS61310
+5V
R1 ()
T1 100 50 50
+
33 F RGND 28 CLKE
M C LK
0.1 F 21 RV+ 15 TV+
+
1.0 F TGN D
R2 ()
SCLK
CS
27 26 23 24 25 P S e ria l P o rt
C o ntro l & M o nitor
1 12 6 18 11
LO S BPV LA TN JA S E L 5 MODE RPO S RNEG
RCLK
IN T SDI SDO CS61310 IN HOST MODE
RV+ 1 k 7 6 F ra m e F o rm at E n c o d er/ D e co d er 8 3 4 2 9 10
R T IP
19
R1
1 0.47 F 5
2 R E C E IV E L IN E 6
R R IN G
20
R2
1C T :1 P E -6 4 9 3 6 0.47 F
TPOS TNEG TCLK X T A L IN XTALOUT RGND 22 TG ND 14 T R IN G TTIP 16 13 2 6 1:1 .5 T-10 5 4 1 T R A N S M IT 5 L IN E
Figure 14. Matched Impedence Output Configuration
28
DS440F1 FEB `03
* Notes *

▲Up To Search▲

Price & Availability of CS61310-IL

	To Download CS61310-IL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .